Product Description
REBUILT PERFORMANCE CHRYSLER/TURBO DODGE 2.2/2.5 CYLINDER HEADS
PERFORMANCE 782 “FAST BURN” CASTING HEAD
We offer a selection of professionally rebuilt PERFORMANCE upgraded genuine Chrysler 2.2/2.5 cylinder heads with a complete selection of performance upgrades for use on both normally aspirated and turbo charged engine applications for the Chrysler, Plymouth and Dodge automobiles built from 1983 to 1993 and utilizing the popular 2.2 and 2.5 liter engines.
These guaranteed genuine Chrysler manufactured cylinder heads have been professional machine shop refurbished and completely rebuilt including deep chemical cleaning, pressure tested for leaks and inspected for cracks, block to head surface resurfacing, new valve seats, new valve guides with integrated locks, new positive clad valve stem seals and on stock and performance heads a complete 3 angle valve job, assembled height and spring pressures checked and within factory performance specs, stock slider turbo camshaft (287) or 88 TBI roller(782), slider (287) or roller (782) cam followers. The non-bare heads are delivered completely loaded ready to be installed with all the typical installation accessories, gaskets and needed hardware.
Each “PERFORMANCE” upgraded Chrysler 782 2.2/2.5 cylinder head is delivered fully loaded with the following:
- Professional machine shop rebuilt cylinder head
- Resized +1mm valve seats w/ 3 angle max performance valve job
- Back cut intake and exhaust valves for more flow and horsepower
- +1mm Stainless Steel Performance Intake & Exhaust Valves
- HD Crane Valve Springs
- Mopar Performance Hardened Intake/Exhaust Valve Locks/Keepers
- OEM Valve Spring Retainers
- OEM Roller Cam Followers
- New valve guides w/locks
- New OEM 88 TBI Cam
- Front and Rear Cam Seals
- Mopar Performance PT Lifters With Shims
- Turbo Dodge Parts Positive Clad Valve Stem Seals
- Turbo Dodge Parts Ultimate intake studs
- Turbo Dodge Parts Ultimate exhaust studs with copper clad flange nuts
- FelPro 10mm or 11mm head bolts
- FelPro Valve Cover Gasket (1 piece or multi-piece design)
- FelPro PermaTorqe head gasket
- FelPro Intake/Exhaust manifold gasket
- No cylinder head core required
- Full 1 Year Unlimited Mileage Warranty
Conical Valve Springs w/keepers and locks 
*** STANDARD ON PERFORMANCE HEADS ***
BACK CUT VALVES FOR MORE FLOW AND HORSEPOWER
After the valves have been lapped, a backcut is placed on the back of the valve, close up to the inner edge of the 45° seating area. This further improves flow around the head of the valve.
On the inlet valve, the lap marks should be placed on the outer edge of the 45° valve face. This takes full advantage of the diameter of the valve. When the lap marks sit inside the outer edge of the valve, the overhanging portion of the valve serves as an obstruction to flow. The top cut on the seat (usually 30 degrees), establishes the outer edge of the seat and helps turn flow into the combustion chamber. A 60 degree bottom cut sets the width of the 45°seat.
The 45° exhaust seat is deliberately kept inboard of the outer edge of the valve – otherwise hot exhaust gas will eventually erode the edge of the valve.
Look at a typical stock replacement cylinder head and you’ll find they have a basic 45° angle cut on to the seat. On these heads, you can lap in the valves and inspect the valve face to see exactly where the seat is coming in contact with the valve face. Even on aftermarket heads that come out of the box with a three angle cut, when you lap in the valves you’ll often see the angles haven’t been placed for optimum performance.
The graph below shows the results of a typical flow test carried out on a brand new CNC 044 cylinder head (40mm inlet valve).
- The red line shows ‘out of the box’ flow with the factory fresh 3 angle seat.
- The green line shows the improvement by recutting and repositioning the 45° cut to the outer edge of the valve.
- The blue line indicates flow when a 30° back cut to the valve was added.
Red line: straight out of the box with no mods
Green line: 3 angle valve job
Blue line: 3 angle valve job plus 30° backcut on the valve
Overall gain in flow @ .500″ lift: 14cfm
This illustrates how even the mildest of engine builds will benefit from the addition of a decent valve job. On a mild 4 cylinder engine build, this modification alone could account for an increase of 10bhp or more.
ACTUAL MEASURABLE DYNO RESULTS!
Here is a typical dyno sheet that compares a stock 782 cylinder head performance with one of our performance cylinder heads performance. Blue run is years ago with stock head and 15 psi. Red run is today with 18psi spike 15psi hold. Turbododgeparts.com performance head will get you 30hp and 30tq.. ish.
 |
 |
 |
